Contents and categories

Display all

Contents and categories

Series

Search suggestions

Display all results

TINO SYSTEM

Switching System 2 Guitar Amplifiers to 1 Cabinet with Remote Input
Item No.: PTINOS
The Palmer TINO SYSTEM - The clever solution for switching two amps to 1 cabinet

Ambitious guitarists often use two amplifiers in order to obtain different basic sounds. However, transport, space restrictions and the decrease in output associated with PA speakers can be very inconvenient. This is where TINO S promises to help. The switcher system allows you to use two amplifiers with only one box as an alternative. Regardless of whether you use tube amplifiers that require getting a load, or transistor models. Even a mixed combination is possible without any problems.

The switch-over between the amplifiers can be operated via a pressure switch on the device or via an optional standard foot switch or switching system. If the switch cannot be done with a switching system, a standard foot switch can be connected to the corresponding 6.3 mm jack. (Requires a switch, not push-buttons!)

TINOS routes the guitar signal to the chosen amplifier, while the second unused amplifier is turned off to prevent unwanted interference. (As if the potentiometer on the guitar was switched off). The gain from the instrument input to output is one (Unity Gain). The built-in buffer only converts the impedance, so that a high-impedance guitar becomes less prone to interference. When the guitar signal is switched, the speaker is switched simultaneously, while the speaker output from the mute amplifier is connected to a load (Dummy Load). Therefore, tube amplifiers are absolutely safe from dangerous idling.

If you connect two amplifiers with one another, a heavy buzzing sound often overlays the guitar signal. This undesirable effect is known as ground loop and occurs between mains-operated devices because of double grounding. The TWO IN ONE prevents this from happening by decoupling the outputs to the amplifiers using high-quality isolating repeaters.A smooth switching between the amplifiers also ensures that the process takes place without crackling in the loudspeaker. The power supply is provided via the supplied 9V power adapter.

 

Contents and categories

Display all

Contents and categories

Series

Search suggestions

Display all results
The Palmer TINO SYSTEM - The clever solution for switching two amps to 1 cabinet

Ambitious guitarists often use two amplifiers in order to obtain different basic sounds. However, transport, space restrictions and the decrease in output associated with PA speakers can be very inconvenient. This is where TINO S promises to help. The switcher system allows you to use two amplifiers with only one box as an alternative. Regardless of whether you use tube amplifiers that require getting a load, or transistor models. Even a mixed combination is possible without any problems.

The switch-over between the amplifiers can be operated via a pressure switch on the device or via an optional standard foot switch or switching system. If the switch cannot be done with a switching system, a standard foot switch can be connected to the corresponding 6.3 mm jack. (Requires a switch, not push-buttons!)

TINOS routes the guitar signal to the chosen amplifier, while the second unused amplifier is turned off to prevent unwanted interference. (As if the potentiometer on the guitar was switched off). The gain from the instrument input to output is one (Unity Gain). The built-in buffer only converts the impedance, so that a high-impedance guitar becomes less prone to interference. When the guitar signal is switched, the speaker is switched simultaneously, while the speaker output from the mute amplifier is connected to a load (Dummy Load). Therefore, tube amplifiers are absolutely safe from dangerous idling.

If you connect two amplifiers with one another, a heavy buzzing sound often overlays the guitar signal. This undesirable effect is known as ground loop and occurs between mains-operated devices because of double grounding. The TWO IN ONE prevents this from happening by decoupling the outputs to the amplifiers using high-quality isolating repeaters.A smooth switching between the amplifiers also ensures that the process takes place without crackling in the loudspeaker. The power supply is provided via the supplied 9V power adapter.

Specifications
General
Product type Switches
Type amp switcher
Switching function output switcher
Inputs 2
Input connectors 6.3 mm jack
Input impedance 10 M Ohm(s)
Outputs 1
Output connectors 6.3 mm jack
Output impedance 10 k Ohm(s)
Transformer isolated outputs no
Indicators channel number
Controls channel switching, ground lift
Operating voltage 9 V DC power supply
Max. Current 130 m
Cabinet material sheet steel/aluminium
Cabinet surface powder coated/anodized
Width 222 mm
Depth 175 mm
Height 44 mm
Accessories (included) 9 VDC power adapter
Weight 1,562 kg
Downloads & links
Name
Category
Type
File size
Palmer Catalogue Catalog pdf 22 MB
Product images Image files zip -
User's manual Manual pdf 3 MB
Palmer Catalogue

Category: Catalog

Type: pdf

File size: 22 MB

Product images

Category: Image files

Type: zip

File size: -

User's manual

Category: Manual

Type: pdf

File size: 3 MB

(0) Download files
Related Products
Buy
No suitable online shop found? Then search on Google Shopping Or find a local dealer: